Description:
Further evolution of the standard ESC
The Tornado Design Heat Sink is adopted to further improve the excellent basic performance and ease of handling, realizing an overwhelming amount of heat dissipation that is classless. The surface area and exhaust heat flow have been optimized to ensure stable operation even under heavy load.
Realization of tough hardware that is the foundation of everything.
High-capacity heat sink that penetrates the two-layer board
Board wiring using pure copper plates
Latest FETs with ultra-high efficiency and low ohms
Firmware compatibility chart (as of April 2022)
PROGBOX
| |
TS160A |
TS120A |
TS90A , BLS90 |
TS50A |
BLC50 |
| Ver 2.xx |
OK |
OK |
OK |
OK |
OK |
| Ver 1.xx |
INCOMPATIBLE |
OK |
OK |
OK but cannot be used for Ver1.061.07 |
OK but cannot be used for Ver1.061.07 |
| |
|
|
|
|
|
G FORCE LINK(PC)
| |
|
TS160A |
TS120A |
TS90A |
TS50A |
BLC50 |
| Ver 2.xx |
Supported OS
Windows 8.1
Windows 7
Windows XP
|
OK |
OK |
OK |
OK |
OK |
| Ver 1.xx |
Supported OS
Windows 7
Windows Vista
Windows XP
|
INCOMPATIBLE |
OK |
OK |
OK |
OK |
Wi-fi Link (Mobile phone application) Correspondence table
| |
TS160A |
TS120A |
TS90A |
TS50A |
TS50A REV |
1S120A |
| Ver 1.21 |
OK |
OK |
OK |
INCOMPATIBLE |
INCOMPATIBLE |
OK |
| Ver 1.2 |
BEC voltage cannot be switched. |
OK |
OK |
INCOMPATIBLE |
INCOMPATIBLE |
OK |
| Ver 1.1 |
× |
OK |
OK |
INCOMPATIBLE |
INCOMPATIBLE |
OK |
Product Specifications
| Continuous maximum current/Instantaneous maximum current |
|
| Applicable motors |
Brushless motor with sensor & sensorless motor |
| Compatible scale |
1/10 Electric Car, 1/12 Electric Car |
| Usable turns |
NiMH (6.0V to 7.2V) or 2S LiPo (7.4V) 5.5T or more (1/10 Touring Car), 7.5T or more (1/10 Buggy)
This is the case when Turbo Boost is not used. If Turbo Boost is used, the load on the ESC will increase dramatically and the possibility of damage will increase. Please use a gear ratio and number of turns that allows for a sufficient margin.
NiMH(9.6V-10.8V) or 3S LiPo(11.1V) 6.5T or higher (1/10 Touring Car), 9.5T or higher (1/10 Buggy)
Do not use the Turbo Boost function when using NiMH (9.6V to 10.8V) or 3S LiPo (11.1V), as it will damage the ESC.
|
| Resistance |
0.0005 Ω |
| Compatible battery |
NiMH(4.8V〜10.8V) or 2-3S LiPo(7.4V〜11.1V) |
| BEC voltage and current |
6V@3A |
| Size |
39x38x20mm (LxWxH) |
| Weight |
38g (excluding wires and fan) |
| Cooling FAN Operating Conditions |
8V@0.2A , MAX 12.6V |
| Throttle direction |
Forward/brake", "Forward/reverse", "Forward/brake/reverse"
The factory default setting is "Forward/Brake".
To change the setting, it is necessary to use PROBOX (G0017) or Wi-Fi Link (G0034) (sold separately).
|
*This is for 2.4GHz transmitter/receiver only; may not work at 27MHz or 40MHz.
X (Twitter)
Facebook
